Winter heating maintenance for a commercial building in the Cleveland area comes down to three things: a full heating startup before the cold arrives, regular in-season checks on filters, safeties, venting, and freeze protection, and a plan for the cold snaps that push equipment to its limits. Most buildings do the first and skip the other two, which is why so many no-heat calls come in January rather than October.
This fall we wrote about what a real commercial heating startup checks. This post picks up where that one ends: what keeps a building’s heat running from the first frost to the last one, for facility managers and building owners responsible for offices, schools, healthcare facilities, warehouses, and industrial plants across Northeast Ohio.
Why does commercial heating need maintenance during the winter, not just before it?
A startup proves that equipment works on the day it was tested. Winter is what happens next: months of near-continuous run hours, freeze-thaw cycles, lake-effect snow, and wind across the roof. Components that passed in October wear through by February. Filters load up. Condensate lines that drained fine in mild weather freeze. Snowdrifts block vent terminals that were clear when the technician left.
Cleveland’s heating equipment also faces a handful of nights each winter that drop into the single digits, and some winters go below zero. Commercial heating systems are sized to hold temperature at roughly those conditions with little to spare. On those nights, a unit running at 80% of its capacity because of a dirty filter or a weak burner is the difference between a comfortable building and a cold one.
What does winter heating maintenance include?
For most commercial buildings, in-season maintenance is a short list done consistently:
- Filters. Heating season run hours load filters faster than people expect. A clogged filter reduces airflow across the heat exchanger, which raises its temperature, trips high limits, and shortens its life. Make-up air units, which heat outdoor air for kitchens and process exhaust, are often the worst offenders.
- Burner and flame performance on any unit that has locked out or reset since the startup. A unit that needed a reset once will need one again, usually at a worse time.
- Venting and intake terminals. High-efficiency boilers and furnaces often vent through a sidewall or roof with PVC terminals close to the snow line. A drift that covers the vent or the intake shuts the appliance down at best and pushes combustion gases back at worst. Clearing them after every significant snowfall is part of winter maintenance.
- Condensate lines. Condensing equipment produces water all winter. Lines that run outdoors or through unheated spaces freeze unless they are protected, and a frozen drain shuts the equipment down.
- Freeze protection. Freezestats, outdoor air damper operation, and glycol strength on hydronic coils that see outside air. These protect against one of the most expensive winter failures there is: a split coil and the water damage that follows.
- Controls and alarms. Confirm that building automation alarms for low space temperature, burner lockout, and low supply water temperature actually reach someone who will act on them, including on weekends.
How often should commercial heating be serviced in the winter?
As a baseline, every commercial heating system should get a full startup in the fall and at least one mid-season inspection, typically in January, after the first stretch of hard cold. Buildings with heavy heating loads, make-up air units, boiler plants, or critical occupancies such as healthcare and laboratories benefit from monthly checks during the heating season. Filters follow their own schedule, based on how quickly they load in that building.
The easiest way to make that schedule happen is to put it in a commercial HVAC maintenance program, so the mid-winter visit is on the calendar before anyone has a reason to forget it.
What should facility staff watch for between service visits?
Building staff are the early warning system. These signs are worth a call before they become an emergency:
- Zones that run cold in the morning and catch up by afternoon — often the first sign of a unit losing capacity.
- Equipment that locks out and runs normally after a reset.
- Short cycling: burners that light, run briefly, and shut off over and over.
- Exterior doors that are hard to open or slam shut, a sign the building is running negative because make-up air isn’t keeping up.
- Ice forming at vent terminals, on condensate lines, or on the roof around rooftop units.
- A gas bill rising faster than the weather explains.
- Any carbon monoxide alarm. Treat it as an emergency, clear the area, and call the gas utility and a qualified technician.
How should a commercial building prepare for a cold snap?
When the forecast shows a stretch of single-digit or below-zero temperatures, a little preparation the day before saves a lot of trouble:
Reduce overnight setbacks. A deep unoccupied setback that works in December may leave a building unable to recover by morning in extreme cold. Raising the setback temperature for those nights keeps equipment from starting the day hopelessly behind.
Check the vulnerable spots. Vestibules, loading docks, stairwells, and mechanical rooms with exterior walls are where pipes freeze first. Make sure their heaters work and their doors close.
Confirm freeze protection and alarms. Outdoor air dampers should close when units are off, and someone should be watching low-temperature alarms overnight.
Know who to call. If something fails at 2 a.m. on the coldest night of the year, the time to find out how your contractor handles emergencies is not then. Here is how our emergency service works.
We have written in more detail about where commercial rooftop units fail in prolonged freezing temperatures, and our guide to commercial HVAC maintenance and common repairs covers the year-round picture.
The bottom line
The buildings that get through a Cleveland winter without a no-heat call usually aren’t lucky. Someone started up the heat properly in the fall, checked it again after the first hard freeze, kept the vents clear of snow, and had a plan for the coldest week of the year. None of it is complicated. It just has to happen every year.
Air Temp Mechanical has maintained heating systems for commercial, industrial, institutional, and healthcare buildings across Cleveland and Northeast Ohio since 1978 — rooftop units, make-up air units, boilers, and the controls that run them. If you’d like a mid-winter inspection, or a maintenance program that schedules it for you, our commercial HVAC service team can help. Get in touch.



